Search Results

Search results 1-20 of 28.

  • User Avatar

    Hi, Yes it's'the Creatures Update i have to talk with my IT. Maybe they can remove it. I hope also we can get a fast response from F&S. Greetings.

  • User Avatar

    Hi, I have to check it....

  • User Avatar

    Hello, we have installed a computer with windows 10 and we want to connect to to the netdcu board "netdcu9". But we get no connection to the board. Neither with windows 10 synchronizing centre nor with the windows mobile device centre. Any ideas where to look ? Greetings

  • User Avatar

    touch config default parameter

    telerob - - NetDCU9

    Post

    Hello together, can someone tell me what are the default parameter of the touch display for NetDCU 9.2? Greetings.

  • User Avatar

    Thanks, it's working. But will this installation issue under windows 10 soon be fixed?

  • User Avatar

    Hello, I tried under windows 10 (logged in as local administrator) a kernel uodate with the netdcu usb loader 2.4.1 After connecting the serial and usb cable and starting the kernelupdate process in the bootlader menu with DU, i got following message from the dcuterm shell: +USB_Init() RNDISFN: UFN_RESET received RNDISFN: UFN_RESET received RNDISFN: UFN_RESET received than it stops In the application NetDCU-USB-Loader the red LED don't switch to green. After checking the forums i tried to instal…

  • User Avatar

    I use fsimx6-V2.1 we also added some packages based on the minimal configuration. Network is initialized over the /etc/network/interfaces.conf: Source Code (19 lines) This is my buildroot configuration: Source Code (49 lines)

  • User Avatar

    This is the code which is used... Source Code (13 lines) Kernel output.... check first line and last lines Source Code (13 lines) Limiting the speed in U-Boot works as you suggested. But as soon as the kernel is started it switches back to 1GBits.

  • User Avatar

    I applied the kernel patch and tested it. Nothing changed.... link speed is still 1000MBit. PHY: 1:04 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready I didn't change the rate in u-boot..... Any ideas? I also see a different in U-Boot and C example: val &= ~0x0300; vs dio write FEC 0 3300

  • User Avatar

    rtprio - normal user

    telerob - - efusA9 Freescale i.MX6

    Post

    Yes, after compiling this package in, I have a limits.conf file. But it is still not working. I also added pam to busybox, without success. I'm not sure but as I see, all settings in limits.conf are applied as soon the user logs in. In my case, the process is started by start-stop-daemon which switches to another user and then start the executable. So I don't know if settings are applied... I also don't know if pam is working because I don't know how I would see this. Is there any other possibil…

  • User Avatar

    rtprio - normal user

    telerob - - efusA9 Freescale i.MX6

    Post

    Hello, in our application some threads run with rtprio. If I start the program as root, everything works as expected. If starting as normal user it is not possible to change the priority to rt. I know that this is nothing special, because not all users have the same rights. On a "normal" Linux systems I modify the /etc/security/limits.conf file. On the device, there is no such file and also after creating it, it is not used by the system. Any ideas?

  • User Avatar

    TV in/out

    telerob - - efusA9 Freescale i.MX6

    Post

    That sounds good, but is it right, that there are no hardware encoders for H.264?

  • User Avatar

    TV in/out

    telerob - - efusA9 Freescale i.MX6

    Post

    Some time ago we did some tests with the imx6 and its hw encoder/decoder capabilities. We are very happy with the performance but we need to integrate it into an "old" system. One device should act as an encoder for fbas/composite PAL signal to h.264 and on the other side backwards from h.264 to fbas/composite PAL. Is there an "easy" solution to get fbas into the system and fbas out?

  • User Avatar

    Rebuild Compiler

    telerob - - efusA9 Freescale i.MX6

    Post

    Hi, is there any reason why you don't build the compilers/gdb with buildroot? We have some issues running gdb from the toolchain because we have a 64bit system and there are missing dependencies (python2.7 386). [Update] Compiling Buildroot with its own toolchain seems to work with the minimal configuration. After installing the libpython2:i386 package the toolchain provided by F&S also works fine. Maybe we change over to a newer gcc because of C++11 but at the moment we will use 4.7.

  • User Avatar

    I tried to update my efusA9 to the new release (V2.1) over a SD-Card. Therefore I renamed install.scr to update.scr. If I insert the card into the micro-sd slot, U-Boot doesn't start the update. If I insert it into to std sd slot the update starts and everything is fine. Our current design only uses the micro-sd connector (SD_A_xx signals) do we need to modify U-boot (in source) or is it easier to change our design? Are there any other restrictions if we only use the micro-sd signals?

  • User Avatar

    Oh, thanks :). We need it for linux.

  • User Avatar

    We use the efusA9 as a replacement for an old CPU board. For ethernet we use an RJ45 connector which only supports 100Mbits (4 wires). As the efusA9 supports 1GBits I don't know what will happen if we use a 1Gbit switch (we only have 1Gbit network). How can we limit the device to only use 100MBit?

  • User Avatar

    Registry entry TYPE in Platform

    telerob - - NetDCU9

    Post

    Hello, we want to check if F3S is installed or not on our netdcu9. We found an entry in the registry (F3SSerial) which did the trick. But there is another entry we didn't see before: type. (see attachment) What does this key stand for? Regards

  • User Avatar

    Good morning, I reformatted the flash disk and the system has found now a bad block. Can you give an idea under what circumstances this can happen? What i know from my colleagues is that they unplugged the netcdu9 from one power supply and plugged it in in another power supply? Greetings

  • User Avatar

    Hello, i did not call SetLastError before. I tried to copy a file on ffsdisk, but it is not possible. Copying files on a attached USB memory is possible. It is also possible to create a file with the fopen-function on the USB-memory Greetings