Change armStoneA5 from Linux to WEC2013

      Change armStoneA5 from Linux to WEC2013

      Hello,

      I want change the SW on my armStoneA5 Board from Linux to WEC2013.
      First I've erased the Flash from and updated NBoot to V 08 and than I've updated EBoot to V 07.
      After Update EBoot and start of EBoot I've to enter the MAC address, but than I became an error message:

      F&S Nand Loader VN08 built Apr 2 2014 08:57:42
      armStoneA5 Rev. 1.10
      256MB RAM (1 chip) 128MB FLASH (92f1) 500MHz 512kB L2
      booted primary image from page 4
      serial number not set

      Please select action
      'd' -> Serial download of bootloader
      'E' -> Erase flash
      'B' -> Show bad blocks
      Use NetDCUUsbLoader for USB download

      Bad blocks: None

      Erasing.................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Done

      Please select action
      'd' -> Serial download of bootloader
      'E' -> Erase flash
      'B' -> Show bad blocks
      Use NetDCUUsbLoader for USB download

      Bad blocks: None

      Waiting for EBoot, U-Boot, NBoot, M4 Image...
      ................................................................ 65536 Bytes
      ................................................................ 131072 Bytes
      ................................................................ 196608 Bytes
      ................................................................ 262144 Bytes
      ................................................................ 327680 Bytes
      ................................................................. 393216 Bytes
      Success, checksum: 0x338d

      >>> EBoot image loaded (393216 bytes) <<<

      Please select action
      'f' -> Save image to flash
      'x' -> Execute image
      'd' -> Serial download of bootloader
      'E' -> Erase flash
      'B' -> Show bad blocks
      Use NetDCUUsbLoader for USB download

      Saving EBoot
      Success

      >>> EBoot image loaded (393216 bytes) <<<

      Please select action
      'f' -> Save image to flash
      'x' -> Execute image
      'd' -> Serial download of bootloader
      'E' -> Erase flash
      'B' -> Show bad blocks
      Use NetDCUUsbLoader for USB download

      <-2>Windows CE ethernet MAC address not set.
      Enter WindowsCE MAC address (actual ff:ff:ff:ff:ff:ff): 00055108ffd6
      MAC address for WindowsCE set to 00:05:51:08:ff:d6
      ReadData: failed to read sector (0x480).
      ERROR: Flash read failed.
      WARNING: MainMenu: Failed to store updated bootloader configuration to flash.

      armStoneA5 - WindowsCE Bootloader

      :>


      If I now send the WEC2013 Kernel with NetDCUUsbLoader all Flash Blocks from 18 - 1023 will be marked as Bad Blocks.

      What can I do or what I've made wrong ?

      Best Regards
      Joachim
      Hello Mr. Zeller,

      this problem is allready known to us. This would be correct this week in the next Eboot version. I will inform you as soon as new Eboot version is available.
      F&S Elektronik Systeme GmbH
      As this is an international forum, please try to post in English.
      Da dies ein internationales Forum ist, bitten wir darum, Beiträge möglichst in Englisch zu verfassen.
      Hello Mr. Zeller,

      new eboot version is in the download area now. That is a beta version (EBOOT_08_BETA.nb0). The oficial release is coming soon.
      F&S Elektronik Systeme GmbH
      As this is an international forum, please try to post in English.
      Da dies ein internationales Forum ist, bitten wir darum, Beiträge möglichst in Englisch zu verfassen.
      Hello Mr. Zeller,

      the official EBoot V0.8 version was released and available in download area.
      F&S Elektronik Systeme GmbH
      As this is an international forum, please try to post in English.
      Da dies ein internationales Forum ist, bitten wir darum, Beiträge möglichst in Englisch zu verfassen.