Hi,
I succeeded to put the uboot and the kernel on the board.
This is what i see on when the board boots:
]
U-Boot 1.3.3 (Jun 12 2008 - 14:44:43)
PicoCOM1 (c) 2008 emlix GmbH
I2C: ready
DRAM: 32 MB
NAND: 32 MiB
*** Warning - bad CRC or NAND, using default environment
WDC: disabled
In: serial
Out: serial
Err: serial
Net: macb0
macb0: link down (status: 0x7849)
Hit any key to stop autoboot: 0
Loading from NAND 32MiB 3,3V 8-bit, offset 0x100000
Image Name: emlix gmbh - F+S PicoCOM1
Created: 2008-06-12 15:00:37 UTC
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 1418809 Bytes = 1.4 MB
Load Address: 20008000
Entry Point: 20008000
## Booting kernel from Legacy Image at 21000000 ...
Image Name: emlix gmbh - F+S PicoCOM1
Created: 2008-06-12 15:00:37 UTC
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 1418809 Bytes = 1.4 MB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.6.25-Eval-BSP-1.0 (root@kserv) (gcc version 4.2.4 (Emlix Linux PicoCOM1 Eval-BSP-1.0)) #1 PREEMPT Thu Jun 12 14:33:57 UTC 2008
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: PicoCOM1 - AT91SAM9260 based
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 198 MHz, master 99 MHz, main 18.432 MHz
CPU0: D VIVT write-back cache
CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS1,38400,8n1 root=/dev/mtdblock4 rootfstype=jffs2
AT91: 96 gpio irqs in 3 banks
PID hash table entries: 128 (order: 7, 512 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 29452KB available (2692K code, 201K data, 92K init)
SLUB: Genslabs=12, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 152 bytes
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(0.382:1): initialized
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.9)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
atmel_usart.0: ttyS0 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL
enable RS485 on port0...done
atmel_usart.1: ttyS1 at MMIO 0xfffb8000 (irq = 
is a ATMEL_SERIAL
console [ttyS1] enabled
atmel_usart.2: ttyS2 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
ssc ssc.0: Atmel SSC device at 0xc2868000 (irq 14)
F&S I/O Driver loaded (fsio char devices major nr. 60)
picocom_adc: ADC with 3 ports on fsio6 ready
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfffc4000 irq 21 (00:05:51:01:90:f5)
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00, irq=-1)
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit)
AT91 NAND: 8-bit, Software ECC
Scanning device for bad blocks
Creating 5 MTD partitions on "at91_nand":
0x00008000-0x00048000 : "U-boot Bootloader"
0x00048000-0x00050000 : "U-Boot Environment"
0x00050000-0x00100000 : "User Block"
0x00100000-0x00280000 : "Kernel raw"
0x00280000-0x02000000 : "User Block targetfs"
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
at91_ohci at91_ohci: irq 20, io mem 0x00500000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
pcf8563 0-0051: chip found, driver version 0.4.2
pcf8563 0-0051: rtc core: registered pcf8563 as rtc0
i2c-gpio i2c-gpio: using pins 23 (SDA) and 24 (SCL)
at91sam9_wdt: Watchdog register already programmed.
at91_mci: Card detect thread activated
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
can: controller area network core (rev 20071116 abi
NET: Registered protocol family 29
can: raw protocol (rev 20071116)
can: broadcast manager protocol (rev 20071116)
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
registered taskstats version 1
pcf8563 0-0051: low voltage detected, date/time is not reliable.
pcf8563 0-0051: retrieved date/time is not valid.
pcf8563 0-0051: hctosys: invalid date/time
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing init memory: 92K
Warning: unable to open an initial console.
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
Any idea ?
