Hi,
we tried to install the additional purchased SPI driver (nspi.CAB, 29.09.2006).
After installing the PicoMOD3 isn't booting anymore:
Code
- Microsoft Windows CE Ethernet Bootloader Common Library Version 1.1 Built May 29 2008 15:00:11
- Microsoft Windows CE Bootloader for PicoMOD3 Built Jun 12 2008
- Portions copyright (c) 2007 F&S Elektronik Systeme GmbH
- Boot Loader, Version 1.35
- StepStone Loader, Version P313
- (NAND ID:0x2076) --> ST: 512MBit (64MB)
- OK.
- NUM_OF_BLOCKS = 4096
- PAGES_PER_BLOCK = 32
- SECTORS_PER_PAGE = 1
- Block 0 to 18 are locked for boot loader
- Create partition for boot section ... Success
- System ready!
- Preparing for download...
- Press >S< to step into monitor...
- AUTO BOOT enabled
- Kernel read from flash disk started
- finished
- INFO: OEMLaunch: Jumping to Physical Address 0x301420FCh (Virtual Address 0x0h)...
- Windows CE Kernel for ARM (Thumb Enabled) Built on Jun 16 2009 at 10:08:15
- PicoMOD3 V0.27 - Firmware Init
- Copyright (c) 2008 F&S Elektronik Systeme GmbH
- Build: Apr 1 2011/10:08:45
- INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
- FCLK:534000000, HCLK:133500000, PCLK:66750000
- HW-WATCHDOG: ENABLED
- FMD: NAND ID:0x2076 --> ST: 512MBit (64MB)
- FMD: Block 0 to 18 are locked for boot loader
- -OEMInit
- +++++++++OEMGetRealTime()
- OALIoCtlHalInitRTC: Year: 2006, Month: 1, Day: 1, Hour: 12, Minute: 0, second: 0
- Time returned from OEMGetRealTime: Year: 2011, Month: 11, Day: 10, Hour: 11, Minute: 40, second: 19
- Drivers\Builtin\Serial1 - OFF
- RestartReason: Reset
- FMD: NAND ID:0x2076 --> ST: 512MBit (64MB)
- FMD: Block 0 to 18 are locked for boot loader
- FMD: FMD_OEMIoControl: unrecognized IOCTL (0x71c24).
- OEM: Not cleaning system hive
- OEM: Not cleaning user profiles
- OEM: Not cleaning system hive
- PM-NETDCU: STARTED
- UART: Version 1.1, Key = Drivers\Active\02
- DEBUG: UART3 SYSINTR : 21
- UART: Version 1.1, Key = Drivers\Active\03
- UART: Version 1.1, Key = Drivers\Active\04
- DEBUG: UART0 SYSINTR : 23
- +OALIoCtlHalGetHWEntropy
- OHCI: Version 1.1, ActiveKey = Drivers\BuiltIn\OHCI
- I2C: Version 2.5, ActiveKey = Drivers\Active\13
- PCC: Version 1.1, ActiveKey = Drivers\Active\14
- AX88796: driver v01.04 for WinCE 6.0
- I2S: Version 1.5, ActiveKey = Drivers\Active\18
- CID: Version 2.5, ActiveKey = Drivers\Active\19
- SDIO: Reset ...ok
- BCS: Version 1.0, ActiveKey = Drivers\Active\31
- NSPI: Version 1.0, ActiveKey = Drivers\Active\32
Is the driver not anymore compatible with the latest firmware?