Posts by Baumann

Baumann · Oct 13th 2015

My Serial out:

Quote

Microsoft Windows CE Bootloader Common Library Version 1.2 Built Feb 2 2015 16:06:34
Microsoft Windows CE Bootloader for armStoneA5 Built Feb 3 2015
Portions copyright (c) 2012 F&S Elektronik Systeme GmbH
Boot Loader, Version 1.3
NBoot, Version VN12
HW rev. 1.10

HW-Watchdog: ON
System ready!
Preparing for download...
Press >S< to step into monitor...
AUTO BOOT enabled
Kernel (2967kB) read from flash disk started finished in 523 milliseconds
INFO: OEMLaunch: Jumping to Physical Address 0x8010BDE9h (Virtual Address 0x0h)...

Jumping to Kernel @ 0x8010BDE9
Windows CE Kernel for ARM (Thumb Enabled)
INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
HW-WATCHDOG: ENABLED

armStoneA5 V2.02 - Firmware Init
Copyright (c) 2013 F&S Elektronik Systeme GmbH
Build: May 13 2015/15:25:42
FMD: NAND ID:0x2cf18095 --> MICRON: 1GBit (128MB)
FMD: Block 0 to 16 are locked for boot loader
I2C: Version 2.5
INFO: No external RTC found!.
OAL: RestartReason=RESETB
FMD: NAND ID:0x2cf18095 --> MICRON: 1GBit (128MB)
FMD: Block 0 to 16 are locked for boot loader
FSPART: FS partition driver loaded
BINFS: RegisterVolume - Mounted volume '\BINFS'
BE2: Version 1.4, ActiveKey = Drivers\Active\03
NI2C: Version 1.0, ActiveKey = Drivers\Active\15
ENET: Version 01.03, ActiveKey = Comm\ETHNETA
ENET: Version 01.03, ActiveKey = Comm\ETHNETB
UsbHost : New Function [address(1) / layer(0)]
FSKBDHID: Version 1.0, ActiveKey = Drivers\Active\20
Attach moutouchHID
TCH: Version 1.8, ActiveKey = Drivers\Active\23
BE2: Version 1.4, ActiveKey = Drivers\Active\24
UART: Version 1.17, Key = Drivers\Active\25
UART: Version 1.17, Key = Drivers\Active\26
UART: Version 1.17, Key = Drivers\Active\27
UART1: Port disabled. Serial debug is on !
CID: Version 2.8, ActiveKey = Drivers\Active\28
CID: Version 2.8, ActiveKey = Drivers\Active\29
AIN: Version 1.2, ActiveKey = Drivers\Active\30
I2C: Version 4.2, ActiveKey = Drivers\Active\31
SDHC: Version 1.2, ActiveKey = Drivers\Active\32
WAV: Version 2.3, ActiveKey = Drivers\Active\34
BCS: Version 1.4, ActiveKey = Drivers\Active\47
NSPI: Version 3.0, ActiveKey = Drivers\Active\48
DIO: Version 2.8, ActiveKey = Drivers\Active\49
FRW: Version 1.1, ActiveKey = Drivers\Active\55
LCD: Version 1.9, ActiveKey = Drivers\Display\LCD
LCD: Read registry settings from Drivers\Display\LCD
SE2: Version 1.3, ActiveKey = Drivers\Active\57
LCD: ASTADPEDT1.dll - Init failed
LCD: Display-Mode 19, Name ET070080 ASA5
TCH: SamplePeriodLowHns =0x1312d00
TCH: SamplePeriodHighHns =0x30d40
TCH: Debug =0xff
TCH: I2CDevAddr =0x94
TCH: ChangeIO =0x57
TCH: ResetIO =0x56
TCH: LogFile =
TCH: I2CDevice =I2C3:
TCH: LogFileDebug =0x0TchProxy: touch driver cann't be loaded. Check touch driver registry settings.

TCH: LogFileTruncate =0x1
TCH: CheckSum =0x0
TCH: InvertX =0x0
TCH: InvertY =0x0
TCH: SWCalibration =0x0
TCH: AutoCalibEventSystem =0x0
TCH: I2CCRC =0x0
TCH: Priority256 =0x6d
TCH: Change-IRQ configured on IO-Pin 87
TCH: Reset-line configured on IO-Pin 86
TCH: Display resolution to scale at detected (800x480).
TCH: Interrupt registered successfully (IRQ=287, SYSINTR=35)
TCH: Initializing Touch controller
TCH: Reinit thread started
I2CLIB: I2C_ReadRegister(): Message failed (flags=8)
TCH: Failed to read Infoblock
TCH: Failed to read Object table
TCH: Driver Failed to Init.
NDCUCFG V 60 started. Platform: armStoneA5
NDCUCFG Open COM1: at 38400 Baud
CreateFile() failed -> ERROR COM1:
CheckAutoStart: Version 1.7, LaunchNum = 100
FSStartup: Version 1.0, LaunchNum = 102
SoftRTC disabled
TCH: Reint thread still active
TCH: Could not enable touch Panel

Display More

All conected through the cable from the kit.

Baumann · Oct 13th 2015

I deleted Registry again and tried it.
But there is still no reaction.

Could it be a Hardware Problem?
At the beginning it was still working but after a few minutes the touch was permanent "activated" at one Point.

Baumann · Oct 12th 2015

Hi,

I deleted registry again and changed only the "flags" values according the Device Driver Document.
But it is does not work.

Registry before:

Code

00 "Prefix"=string:tch \
01 "Dll"=string:fs_touch_sx865x.dll \
02 "Order"=dword:32 \
03 "Index"=dword:1 \
04 "Flags"=dword:33554440 \
05 "IClass"=multi:{25121442-08ca-48dd-91cc-bfc9f790027c};{a32942b7-920c-486b-b0e6-92a702a99b35} \
06 "Priority256"=dword:109 \
07 "SysIntr"=dword:0 \
08 "SampleRate"=dword:200 \
09 "SWCalibration"=dword:1 \
10 "InvertY"=dword:1 \
11 "InvertX"=dword:1 \
12 "Threshold"=dword:800 \
13 "ChangeIO"=dword:99 \
14 "ResetIO"=dword:98 \
15 "I2CDevAddr"=dword:144 \
16 "I2CDevice"=string:i2c3: \
17 "TouchSamples"=dword:3 \
18 "!BoardName"=string:PicoMOD1.2 \
OK
00 "Config" \
OK -> reg enum value \
00 "Prefix"=string:TCH \
01 "Dll"=string:fs_touch_mxt224.dll \
02 "Order"=dword:32 \
03 "Index"=dword:2 \
04 "Flags"=dword:4 \
05 "IClass"=multi:{25121442-08CA-48dd-91CC-BFC9F790027C};{A32942B7-920C-486b-B0E6-92A702A99B35} \
06 "Priority256"=dword:109 \
07 "SysIntr"=dword:0 \
08 "InitialSamplesDropped"=dword:2 \
09 "SampleRate"=dword:200 \
10 "SWCalibration"=dword:0 \
11 "InvertY"=dword:0 \
12 "InvertX"=dword:0 \
13 "ChangeIO"=dword:87 \
14 "ResetIO"=dword:86 \
15 "I2CDevAddr"=dword:148 \
16 "I2CDevice"=string:I2C3: \
17 "LoadAsyncEvent"=string:SYSTEM/ShellAPIReady \

Display More

I changed the touch_sx865x Flags value in "4" (is "33554440" normal?)
and the touch_mxt224 Flags value in "8"
right?

After the Kernel update theres no touch_edt anymore?

Baumann · Oct 9th 2015

Hello Support,

I bought the "aStoneA5-SKIT-W13"-Starterkit and the "SINTF-LVDSTOUCH1"-Capacitive Touch.
I have made the following settings in the registry:

Code

REM
REM Touch MXT224 enable
REM
reg open \drivers\builtin\touch_sx865x
reg set val Flags dword 4
reg open \drivers\builtIn\touch_edt
reg set val Flags dword 4
reg open \drivers\builtIn\touch_mxt224
reg set val Flags dword 8
REM
REM Stream interface Driver
REM
reg open \Drivers\Builtin
reg create key Touch
reg set val Prefix string TCH
reg set val Index dword 1
reg set val Order dword 0xff
reg set val Flags dword 0x8
reg set val IClass multi "{25121442-08CA-48dd-91CC-BFC9F790027C}";"{7119776D-9F23-4e4e-9D9B-9AE962733770}"
reg set val Priority256 dword 0x6D
reg set val DLL string fs_touch_mxt224.dll
reg set val ChangeIO dword 0x57
reg set val ResetIO dword 0x56
reg set val I2CDevAddr dword 0x94
reg set val I2CDevice string "I2C3:"
REM reg set val debug dword 0xffff
REM reg set val LoadAsyncEvent string "SYSTEM/ShellAPIReady"
REM reg set val Flags dword 0x1000008
REM
REM Touch proxy Driver
REM
reg open \hardware\devicemap\touch
reg set val DriverName string tchproxy.dll
reg del val CalibrationData
reg save
reg open \HARDWARE\DEVICEMAP\TOUCH
reg set val Drivername string fs_touch_mxt224.dll
reg set val ChangeIO dword 0x57
reg set val ResetIO dword 0x56
reg set val I2CDevAddr dword 0x94
reg set val I2CDevice string "I2C3:"
reg set val InvertX dword 0x1
reg set val InvertY dword 0x1
reg del val CalibrationData

Display More

and at the beginning the capacitive Touch worked well.

So I tried another touch and changed the registry again. After that I would go back to the first one because it works better.
So I erased the registry and installed the Touch of the starter kit like the first time, BUT it does not work anymore.

My serial Out:

Code

Microsoft Windows CE Bootloader Common Library Version 1.2 Built Feb 2 2015 16:06:34
Microsoft Windows CE Bootloader for armStoneA5 Built Feb 3 2015
Boot Loader, Version 1.3
NBoot, Version VN12
HW rev. 1.10
HW-Watchdog: ON
System ready!
Preparing for download...
Press >S< to step into monitor...
AUTO BOOT enabled
Kernel (2967kB) read from flash disk started finished in 523 milliseconds
INFO: OEMLaunch: Jumping to Physical Address 0x8010BDE9h (Virtual Address 0x0h)...
Jumping to Kernel @ 0x8010BDE9
Windows CE Kernel for ARM (Thumb Enabled)
INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
HW-WATCHDOG: ENABLED
armStoneA5 V2.02 - Firmware Init
Build: May 13 2015/15:25:42
FMD: NAND ID:0x2cf18095 --> MICRON: 1GBit (128MB)
FMD: Block 0 to 16 are locked for boot loader
I2C: Version 2.5
INFO: No external RTC found!.
OAL: RestartReason=RESETB
FMD: NAND ID:0x2cf18095 --> MICRON: 1GBit (128MB)
FMD: Block 0 to 16 are locked for boot loader
FSPART: FS partition driver loaded
BINFS: RegisterVolume - Mounted volume '\BINFS'
BE2: Version 1.4, ActiveKey = Drivers\Active\03
NI2C: Version 1.0, ActiveKey = Drivers\Active\15
ENET: Version 01.03, ActiveKey = Comm\ETHNETA
ENET: Version 01.03, ActiveKey = Comm\ETHNETB
UsbHost : New Function [address(1) / layer(0)]
FSKBDHID: Version 1.0, ActiveKey = Drivers\Active\20
Attach moutouchHID
TCH: Version 1.8, ActiveKey = Drivers\Active\23
BE2: Version 1.4, ActiveKey = Drivers\Active\24
UART: Version 1.17, Key = Drivers\Active\25
UART: Version 1.17, Key = Drivers\Active\26
UART: Version 1.17, Key = Drivers\Active\27
UART1: Port disabled. Serial debug is on !
TCH: Version 1.0, ActiveKey = Drivers\Active\28
CID: Version 2.8, ActiveKey = Drivers\Active\29
CID: Version 2.8, ActiveKey = Drivers\Active\30
AIN: Version 1.2, ActiveKey = Drivers\Active\31
I2C: Version 4.2, ActiveKey = Drivers\Active\32
WAV: Version 2.3, ActiveKey = Drivers\Active\34
SDHC: Version 1.2, ActiveKey = Drivers\Active\33
BCS: Version 1.4, ActiveKey = Drivers\Active\48
NSPI: Version 3.0, ActiveKey = Drivers\Active\49
DIO: Version 2.8, ActiveKey = Drivers\Active\50
FRW: Version 1.1, ActiveKey = Drivers\Active\57
LCD: Version 1.9, ActiveKey = Drivers\Display\LCD
LCD: Read registry settings from Drivers\Display\LCD
SE2: Version 1.3, ActiveKey = Drivers\Active\59
LCD: ASTADPEDT1.dll - Init failed
LCD: Could not intialize external PWM device AstADPEP1 (LE:2)
LCD: Display-Mode 101, Name CHIMEI G070Y2
TCH: Failed to read Infoblock
TCH: Driver Failed to Init.
NDCUCFG V 60 started. Platform: armStoneA5
NDCUCFG Open COM1: at 38400 Baud
CreateFile() failed -> ERROR COM1:
CheckAutoStart: Version 1.7, LaunchNum = 100
FSStartup: Version 1.0, LaunchNum = 102
SoftRTC disabled

Display More

I updated the Kernel and tried it again. But it is still not working
Can someone help me?

Posts by Baumann

Capacitive Touch (WEC2013)

Capacitive Touch (WEC2013)

Capacitive Touch (WEC2013)

Capacitive Touch (WEC2013)