Posts by Zeller

    Hello,


    with DHCP enabled it worked in our network. The board receives an IP address and I can connect.
    But with static IP and disabled DHCP it doesn't work.
    Can you help please.


    Best regards
    Joachim

    Hello,


    I've placed a battery CR2032 in the battery holder of the starter kit, but after every switching off the date and time are lost and I've to set it new to the correct value.
    Is there a problem with the battery power for the RTC on the starterkit at the moment?
    How can I solve this?


    Best regards
    Joachim

    Hello,
    unfortunately this didn't help.
    Here my registry


    My PC has IPv4: 192.168.1.10/255.255.255, No DHCP and shows in the Task Manager "connected"
    The efus board shows in IPCONFIG: Media Stat: Media disconnected for adapter ETHNETA1


    Best regards
    Joachim

    Hello,


    I've programmed the erased board with your manual for programming nboot with the MFG Tool.


    Now I've only the problem that I cannot establish a tcpip connection.
    I always see "Media disconnected" in the console window on efus board but my PC has a connection detected.
    The "Network and Dialup Connections" tool don't start. So how can I set the tcpip parameters in the registry direct with NetDCU Config anf which parameters need to be set.
    I want no DHCP and a static IP Address.


    Best Regards
    Joachim

    Hello,
    ok, I will send back the efus Board to you for install SW new.
    I've now an other efus board in my starter kit. How can I change the IP Address to make a direct connection with my pc (no DHCP Server).
    If I connect the network cable I always see "Media disconnected" in the console window on the efus board but my PC has a connection detected.


    Best Regards
    Joachim

    Hello,
    I've tried serial port A and B, both with Baudrate 115200, data 8, stop 1, Parity none and Handshake none.
    On Port B nothing happens. On Port A every second I receive a 0x00 (<0>) in the Terminal but nothing else..
    Before I've tried to update I used serial port B.


    Best Regards
    Joachim

    Hello,
    I want to install both, i started with NBoot (nbootIMX6SDL_12.bin).
    I've installed this although in the last days because I tryed to solve the problem with the wrong colors by installing all new and there it has worked.


    Best Regards
    Joachim

    Hello,
    the problem with the colors are solved, in the eboot I've selected with XDO the RGB Display (LVDS Display was selected).
    Because of problems with changing the IP Address I've tried erase the whole SW and program it new.
    First I've erased the flash in NBoot, send new NBoot with 'd' and saved them with 'f'.
    Now I've no output on the Terminal, not with 's' or with 'S'.
    If I connect the USB device connector with the cable to the PC, the installation of a driver fails with the message "SE Blank RIGEL - Gerät entfernt"
    Whats the Problem and how can I solve it?


    Best regards
    Joachim

    Hello,
    I've changed the display with the second starter kit and I've also changed the efus module itself, all gave the same wrong result with the colors.
    On the second starter kit all works correct.
    So it seems to be an HW error on the starter kit base board.
    Whats the next steps?


    Best regards
    Joachim

    Hello,
    We've received 2 efus starterkits today.
    On the first boot it works correct, but now the colors on the display of one starterkit are changed. The desktop background is yellow and the top navigation bar is red/pink.
    If I go in the display settings I can change the colors but in the dialog where I can define custom colors the color chart is totaly wrong (See the picture).
    On the base board Ive found 2 little smd resitors which are fallen down, could this be the problem?
    Are there some settings to control?
    Another Point, how can I change the IP Address of the board?


    Best Regards
    Joachim

    Hello,


    I want change the SW on my armStoneA5 Board from Linux to WEC2013.
    First I've erased the Flash from and updated NBoot to V 08 and than I've updated EBoot to V 07.
    After Update EBoot and start of EBoot I've to enter the MAC address, but than I became an error message:



    If I now send the WEC2013 Kernel with NetDCUUsbLoader all Flash Blocks from 18 - 1023 will be marked as Bad Blocks.


    What can I do or what I've made wrong ?


    Best Regards
    Joachim

    Hello,


    I've checked the installation and updates, but I cannot install your sdk, always the error dialog "You must install Visual Studio 2012 before you can proceed with this SDK installation" appears after the installation of the tools. So I've no project template for WEC2013 in Visual Studio 2013.


    The installation of the WEC7 sdk works and I can create a project in VS 2008.


    Best Regards
    Joachim

    Hello,


    for the development with WEC2013 you can use VS2012 or VS 2013 (Microsoft).
    Now I'v installed VS 2013, but I cannot Install your SDK vor ArmStoneA5 WEC2013 (You must install Visual Studio 2012 before you can proceed with this SDK installation).


    Have you a SDK vor WEC2013 and VS2013?


    We want use eventually in future your efus board with WEC2013, is there an SDK for VS2013?


    Best Regards
    Joachim

    Hello,


    I would boot my armstone a5 with a root file system over nfs from a virtual linux machine.
    If I do the settings like described in the documents it doesn't work.
    I receive following outputs in putty:


    VFS: Unable to mount root fs via NFS, trying floppy.
    VFS: Cannot open root device "nfs" or unknown-block(2,0)
    Please append a correct "root=" boot option; here are the available partitions:
    1f00 256 mtdblock0 (driver?)
    1f01 768 mtdblock1 (driver?)
    1f02 512 mtdblock2 (driver?)
    1f03 256 mtdblock3 (driver?)
    1f04 2304 mtdblock4 (driver?)
    1f05 4096 mtdblock5 (driver?)
    1f06 122880 mtdblock6 (driver?)
    Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
    Backtrace:
    [<80035a30>] (dump_backtrace+0x0/0x108) from [<803f179c>] (dump_stack+0x18/0x1c)
    r6:80024d3c r5:8fd2a000 r4:80536ce0 r3:60000013
    [<803f1784>] (dump_stack+0x0/0x1c) from [<803f1b14>] (panic+0x5c/0x17c)
    [<803f1ab8>] (panic+0x0/0x17c) from [<80008dd8>] (mount_block_root+0x1d4/0x218)
    r3:00000004 r2:00000000 r1:8ffcff40 r0:8049257d
    r7:00000000
    [<80008c04>] (mount_block_root+0x0/0x218) from [<80008fc8>] (mount_root+0xc4/0xe8)
    [<80008f04>] (mount_root+0x0/0xe8) from [<8000914c>] (prepare_namespace+0x160/0x1b4)
    r4:80536700
    [<80008fec>] (prepare_namespace+0x0/0x1b4) from [<800089ec>] (kernel_init+0xf0/0x11c)
    r5:80024524 r4:80024524
    [<800088fc>] (kernel_init+0x0/0x11c) from [<80049744>] (do_exit+0x0/0x5f8)
    r5:800088fc r4:00000000


    If I boot with bootubi I can Ping the server (10.0.0.125) but
    mount -t nfs 10.0.0.125:/rootfs /mnt
    doesn't work
    # mount -t nfs 10.0.0.125:/rootfs /mnt
    svc: failed to register lockdv1 RPC service (errno 111).
    lockd_up: makesock failed, error=-111
    mount: mounting 10.0.0.125:/rootfs on /mnt failed: Connection refused


    but if I do
    mount -t nfs -o nolock 10.0.0.125:/rootfs /mnt
    it works.


    What means the option "nolock" and should I use it also while booting and how can I do that?


    Best Regards
    Joachim