Hello FS-Team,
After Network config via telnet and NDCUCFG, I don´t have access over ethernet, maybe I have forgot something... (IP-Adress=set, DHCP=0, Broadcast=0, Gateway=set, Subnet=forgot/not changed)
But the problem is, over serial debug interface there´s also no NDCFG (Debug messages are disabled `O´ = Yes)
Here´s the com1 Debug output:
Code
- <0>12345DeviceID: armStone43110220
- FMD: NAND ID:0xf192 --> EON: 1GBit (128MB)
- [FMD:INF] FMD_Init() : Read ID = 0x0000f192, MID:0x92, DID:0xf1
- FMD: Block 0 to 6 are locked for boot loader
- Create partition for boot section ...
- Success
- Microsoft Windows CE Ethernet Bootloader Common Library Version 1.1 Built Mar 21 2012 14:02:48
- Microsoft Windows CE Bootloader for armStoneA8 Built Mar 21 2012
- Portions copyright (c) 2012 F&S Elektronik Systeme GmbH
- Boot Loader, Version 1.6
- NBoot, Version VN12
- HW rev. 1.10
- HW-Watchdog: ON
- System ready!
- Preparing for download...
- Press >S< to step into monitor...
- 023Windows CE Kernel for ARM (Thumb Enabled) Built on Sep 14 2011 at 17:32:03
- [OAL] ++OEMInit()
- [OAL] ++OEMInit()
- INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
- OAL Log enable : 1
- OAL Log mask : 3
- ******** System Clock Info **********
- [OAL] APLL_CLK : 1000000000 Hz
- [OAL] MPLL_CLK : 667000000 Hz
- [OAL] EPLL_CLK : 96000000 Hz
- [OAL] VPLL_CLK : 54000000 Hz
- [OAL] ARM_CLK : 1000000000 Hz
- [OAL] HCLK_MSYS : 200000000 Hz
- [OAL] PCLK_MSYS : 100000000 Hz
- [OAL] HCLK_DSYS : 166750000 Hz
- [OAL] PCLK_DSYS : 83375000 Hz
- [OAL] HCLK_PSYS : 133400000 Hz
- [OAL] PCLK_PSYS : 66700000 Hz
- ******** System Clock Info **********
- ******** NKForceCleanBoot Change for Release **********
- OEM:-------------------------------------------
- OEM: Normal Boot!!
- OEM:-------------------------------------------
- armStoneA8 V0.01 - Firmware Init
- Copyright (c) 2012 F&S Elektronik Systeme GmbH
- Build: Mar 21 2012/11:54:41
- HW-WATCHDOG: ENABLED
- [OAL] dwNumDram =2
- Invalid time returned from OEMGetRealTime: Year: 2130, Month: 22, Day: 33, Hour: 24, Minute: 30, second: 79
- Resetting real time clock to default date
- Time returned from OEMGetRealTime: Year: 2010, Month: 1, Day: 1, Hour: 12, Minute: 0, second: 0
- MACB: Disabled
- Drivers\Builtin\Serial1 - OFF
- RestartReason: Reset
- FMD: NAND ID:0xf192 --> EON: 1GBit (128MB)
- [FMD:INF] FMD_Init() : Read ID = 0x0000f192, MID:0x92, DID:0xf1
- FMD: Block 0 to 6 are locked for boot loader
- PM-NETDCU: STARTED
- BE2: Version 1.1, ActiveKey = Drivers\Active\01
- DMSG: DrvWAITInitialize
- I2C: Version 3.2, ActiveKey = Drivers\Active\04
- PSS: Version 1.0, ActiveKey = Drivers\Active\13
- AX88796: Version 01.05, ActiveKey =
- NI2C: Version 3.1, ActiveKey = Drivers\Active\21
- UART: Version 1.3, Key = Drivers\Active\22
- UART: Version 1.3, Key = Drivers\Active\23
- BE2: Version 1.1, ActiveKey = Drivers\Active\24
- I2C: Version 3.2, ActiveKey = Drivers\Active\25
- NI2C: Version 3.1, ActiveKey = Drivers\Active\26
- WAV: Version 2.1, ActiveKey = Drivers\Active\27
- UART: Version 1.3, Key = Drivers\Active\28
- <-6>
Regestry clean (R) and Reset to factory default configuration (C) in the shift+s monitor does not help.
So, what can I do now?
Is the kernel-Image anywhere for download?
Thank´s for your help!
