Hi,
I've been experimenting PicoComA5 since a while ago. it used to work fine but after a sudden I could never approach to windows screen. following is the debug output:
Code
- Microsoft Windows CE Ethernet Bootloader Common Library Version 1.1 Built Jul 1 2013 15:25:38
- Microsoft Windows CE Bootloader for PicoCOMA5 Built Jul 2 2013
- Portions copyright (c) 2012 F&S Elektronik Systeme GmbH
- Boot Loader, Version 0.2
- NBoot, Version VN05
- HW rev. 1.10
- System ready!
- Preparing for download...
- Press >S< to step into monitor...
- AUTO BOOT enabled
- Kernel (49183kB) read from flash disk started finished in 6840 milliseconds
- INFO: OEMLaunch: Jumping to Physical Address 0x80108F80h (Virtual Address 0x0h)...
- Jumping to Kernel @ 0x80108F80
- Windows CE Kernel for ARM (Thumb Enabled)
- INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
- OAL Log enable : 1
- OAL Log mask : 3
- 0x83147880
- 0x50
- +OALTimerInit(1 131 0)
- g_pGPC PA=0x4006c000 VA = 0xb006c000
- g_pGPC->LPMR=0x0
- g_pGPC->PGSR=0x8
- g_pCCM->CLPCR=0x78
- cmp=0x83
- PicoCOMA5 V1.01 - Firmware Init
- Copyright (c) 2013 F&S Elektronik Systeme GmbH
- Build: Nov 15 2013/16:31:54
- FMD: g_pNFConReg=0xb00e0000 --> FMD: NAND ID:0x2cf18095 --> MICRON: 1GBit (128MB)
- FMD: Block 0 to 12 are locked for boot loader
- OAL: CPACR=0xf00000 NSACR=0x0
- ========
- CPU Info
- ========
- CPU ID 0xc05
- CPU Revision 0x0 0x1
- Total CPUs 1
- SMP is supported 1
- THUMB is supported 4
- JAZELLE is supported 1
- VFP is supported 1
- UTLB is supported 1
- Maintenance broadcast 2
- Pvt timer freq in MHz 66000000
- =========
- Plat Info
- =========
- Board is RTSM 0
- L2 is extern 0
- Periph Base 0x40002000
- SCU Base 0x40002000
- ==========
- Cache Info
- ==========
- L1 I Sets 512
- L1 I Ways 2
- L1 I Line Sz 32
- L1 I Sz 32768
- L1 D Sets 256
- L1 D Ways 4
- L1 D Line Sz 32
- L1 D Sz 32768
- L2 Sets 0
- L2 Ways 0
- L2 Line Sz 0
- L2 Sz 0
- =========
- Overrides
- =========
- ====================
- OALIoCtlHalInitRTC(2006/1/1 12:0:0.000)
- cBoardConfig.chFeatures1=0x1 0 chBoardType=0x1
- [OAL] MACB: Disabled
- [OAL] RestartReason: <UNKNOWN>
- FMD: g_pNFConReg=0xcc660000 --> FMD: NAND ID:0x2cf18095 --> MICRON: 1GBit (128MB)
- FMD: Block 0 to 12 are locked for boot loader
- PM-NETDCU: STARTED
Do you have any idea what can be the problem?
I think problem has raised when since changed the start up program from explorer.exe to my own software in the registry,however I tried "R" command in the bootloader menu several times after that but no success so yet!
