Hi,
I could not understand how I can read eboot from flash and write it to file. For example to /ffsdisk/backup_eboot.bin or /ffsdisk/backup_eboot.nb0
in ndcucfg is explained:
I do:
Cold you please explain?
thank you
How one can read existing eboot from flash and write it to file?
-
-
Hello,
sorry, i checked the code and saw the "boot read" is not implemented! Unfortunately the "help" for this command is implemente.
Because PV210 is EOL since many years we would not plan to implement this command.
As a workaroud you can read version of eboot from HKLM\Platform and you will find all eboots in our download area.
-
Hello, thank you for answer.
Can you help me to understand how I can change this value 0xd41c65b8 to another one?
Display MoreCode- Microsoft Windows CE Ethernet Bootloader Common Library Version 1.1 Built Nov 19 2014 15:45:58
- Microsoft Windows CE Bootloader for NetDCU14 Built Nov 19 2014
- Portions copyright (c) 2012 F&S Elektronik Systeme GmbH
- Boot Loader, Version 1.14
- NBoot, Version VN20
- HW rev. 1.20
- HW-Watchdog: ON
- System ready!
- Preparing for download...
- Press >S< to step into monitor...
- AUTO BOOT enabled
- Kernel (3043kB) read from flash disk started finished in 724 milliseconds
- INFO: OEMLaunch: Jumping to Physical Address 0x4002BE8Ch (Virtual Address 0x0h)...
- Windows CE Kernel for ARM (Thumb Enabled) Built on Mar 8 2013 at 17:05:33
- [OAL] ++OEMInit()
- INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
- OAL Log enable : 1
- OAL Log mask : 3
- ******** System Clock Info **********
- [OAL] APLL_CLK : 1000000000 Hz
- [OAL] MPLL_CLK : 667000000 Hz
- [OAL] EPLL_CLK : 96000000 Hz
- [OAL] VPLL_CLK : 54000000 Hz
- [OAL] ARM_CLK : 1000000000 Hz
- [OAL] HCLK_MSYS : 200000000 Hz
- [OAL] PCLK_MSYS : 100000000 Hz
- [OAL] HCLK_DSYS : 166750000 Hz
- [OAL] PCLK_DSYS : 83375000 Hz
- [OAL] HCLK_PSYS : 133400000 Hz
- [OAL] PCLK_PSYS : 66700000 Hz
- ******** System Clock Info **********
- ******** NKForceCleanBoot Change for Release **********
- OEM:-------------------------------------------
- OEM: Normal Boot!!
- OEM:-------------------------------------------
- NetDCU14 V1.11 - Firmware Init
- Copyright (c) 2012 F&S Elektronik Systeme GmbH
- Build: May 24 2016/11:03:56
- HW-WATCHDOG: ENABLED
- FMD: NAND ID:0xf192 --> EON: 1GBit (128MB)
- FMD: Block 0 to 6 are locked for boot loader
- [OAL] MACB: Disabled
- [OAL] TVOUT: Disabled
- [OAL] RestartReason: Reset
- [OAL] VidMemBase: 0x4f000000
- FMD: NAND ID:0xf192 --> EON: 1GBit (128MB)
- FMD: Block 0 to 6 are locked for boot loader
- FSPART: FS partition driver loaded
- PM-NETDCU: STARTED
- BE2: Version 1.2, ActiveKey = Drivers\Active\01
- DMSG: DrvWAITInitialize
- PWC: Version 1.0, ActiveKey = Drivers\Active\02
- PSS: Version 1.1, ActiveKey = Drivers\Active\10
- CAM:Version 1.5, ActiveKey = Drivers\Active\11
- CAM:Version 1.5, ActiveKey = Drivers\Active\12
- CAM:Version 1.5, ActiveKey = Drivers\Active\13
- PIF: Version 1.0, ActiveKey = Drivers\Active\16
- OALIntrEnableIrqs -> VirtualIRQ=147 PhysicalIRQ=30
- OALIntrEnableIrqs -> VirtualIRQ=147 IRQ_GPJ3_INT3=147
- AX88796: Version 01.06, ActiveKey = Comm\ETHNETA
- ENC624J600: Version 01.01, ActiveKey = Comm\ETHNETNR
- AX88796: Version 01.06, ActiveKey = Comm\ETHNETB
- AX88796: Controller not found
- BE2: Version 1.2, ActiveKey = Drivers\Active\20
- I2C: Version 4.2, ActiveKey = Drivers\Active\21
- I2C: Version 4.2, ActiveKey = Drivers\Active\22
- NI2C: Version 3.3, ActiveKey = Drivers\Active\23
- NI2C: Version 3.3, ActiveKey = Drivers\Active\24
- CID: Version 2.15, ActiveKey = Drivers\Active\25
- CID: Version 2.15, ActiveKey = Drivers\Active\26
- CID: [1] Device not connected
- AIN: Version 1.1, ActiveKey = Drivers\Active\27
- WAV: Version 2.3, ActiveKey = Drivers\Active\28
- UART: Version 1.4, Key = Drivers\Active\29
- UART: Version 1.4, Key = Drivers\Active\30
- CMM: Version 1.3, ActiveKey = Drivers\Active\31
- SDMMC0: Version 1.7, ActiveKey = Drivers\Active\32
- SDMMC0: Card removed!
- MFC: Version 1.0, ActiveKey = Drivers\Active\46
- JPEG: Version 1.0, ActiveKey = Drivers\Active\49
- MFC power on
- MFC power off
- BCS: Version 1.2, ActiveKey = Drivers\Active\50
- DIO: Version 2.7, ActiveKey = Drivers\Active\51
- OHCI: Version 1.0, ActiveKey = Drivers\BuiltIn\OHCI
- NSPI: Version 3.3, ActiveKey = Drivers\Active\54
- LCD: Version 1.9, ActiveKey = Drivers\Display\LCD
- LCD: Read registry settings from Drivers\Display\LCD
- LCD: LCD_HWInit(512, 2, 0, 0)
- LCD_HWInit: BoardType=0x4
- LCD: Config=0x700000 LCDOut=0x0
- LCD: OutConfig: 24 BIT
- LCD: LCD_SetupGPIOs(EBOOT, 0xd41c65b8)
- LCD: SetDriveStrength =0x3
- LCD: MSignal: TOGGLE
- LCD: HVSignal: TOGGLE
- LCD: Display-Mode 100, Name PrimeView PD064VT4
- LCD: Window BlendPolicy=1
- LCD: m_PrimaryWin: 2, 7, -1, 0xa00001ac, 0xa00001b0, 0xffffffff, 0xffffffff, 0x00000000, 0
- LCD: m_DDOverlayWin: 1, 3, 3, 0xa00001a4, 0xa00001a8, 0xa000064c, 0xa0000650, 0x00000000, 0
- LCD: Before SetMode, GDI will invoke this for Shell
- LCD: Before SetMode, GDI will invoke this for Shell
- LCD: PowerHandler=ON (Mode=0x0)
- LCD_EnablePWM: FALSE
- LCD_EnablePWM: FALSE
- Backlight mode can't be read from registry. Defaulting it to enabled state
- LCD: DispDrvrFS_BacklightControl ON
- LCD: Alloc Primary Surface 640x480, Format 4
- LCD: pixelFormat = OTHER
- LCD: Alloc Primary Surface 0xd30d3400, Buffer 0xd31c0000
- LCD: ScreenWidth:640, ScreenHeight:480, WS:640, HS:480, Rotate:0, PriRot:0
- LCD: DynRotate ScreenW=640, ScreenH=480, ModeW=640, ModeH=480
- LCD: Primary ScreenWidth:640, ScreenHeight:480, Rotate:0
- LCD: ContrastControl not enabled.
- TCHPDD: Version 1.8, Key = HARDWARE\DEVICEMAP\TOUCH
- TCHKEY: Version 1.0, Key = HARDWARE\DEVICEMAP\TOUCH\VirtualKeys
- NDCUCFG V 57 started. Platform: NetDCU14
- CheckAutoStart: Version 1.5, LaunchNum = 100
- NDCUCFG Open COM1: at 38400 Baud
- CreateFile() failed -> ERROR COM1:
- [VDE:INFO] GRP0 phy adr=0x4f000000
- HDMICfg: Version 1.5
- [VDE:ERR] TVD0 Open Device Failed
- USBFN: Version 1.0, ActiveKey = Drivers\Active\69
- USBFN: Serial Function Class Enabled
-
Hello,
what is the problem in detail? Why do you want to change this value?
All possibel display adjustments are described under device driver doc: chapter "display".
-
My setup with new netDCU14 board does not work with LCD display. Old netDCU14 board works in my setup with LCD display correctly.
Same config, all parameters the same, except this value. My suppose is that to have working LCD in my setup, it should be 0xd61d65b8 like in my old netDCu14 board.
-
Hello,
1. are the bootloader and kernel versions the same on "new" and "old"?
2. you can reset the bootloader settings to factory default by bootloader command "C" - afterward you have to flash the kernel again!
Hope this helps.
-
1. yes, the bootloader was the same, and kernel was different.
so I do:
2. I reset bootloader to factory defaults by command "C" and flash the same kernel as sit on old one.
Now I have same eboot, same kernel, same settings and do not work.
the value is now LCD_SetupGPIOs(EBOOT, 0xd61665b8)
-
Hello,
>>same settings and do not work.
<< ok - but i have no idea were does this comes from?
What did you install at all?
Which kernel?
Which bootloder?
PSD?
Display driver setting?
...?
PS: did you confirm "C" case sensitive?
-
Hello,
what I did:
upload through USBloader ebootv210_110, and kernel XIPV210_CE6Core_V1.10_150325.
I start system and press shift+s to upload mentioned files by DU command.
Of course I do command C (capital c) and confirm by Y.
I use PrimeView PD064VT4 LCD - driver settings PrimeView PD064VT4, 640x480 Pixel
Display MoreCode- reg open \drivers\display\LCD
- reg create key mode100
- reg set value name string "PrimeView PD064VT4"
- reg set value EFW dword 11
- reg set value BFW dword 32
- reg set value LPP dword 480
- reg set value msignal dword 2
- reg set value rows dword 480
- reg set value width dword 211
- reg set value height dword 158
- reg set value contrastenable dword 0
- reg set value contrastvalue dword 0
- reg set value type dword 6
- reg set value config dword 7340032
- reg set value columns dword 640
- reg set value HSW dword 64
- reg set value bpp dword 16
- reg set value PPL dword 640
- reg set value lcdclk dword 25
- reg set value VSW dword 2
- reg set value BLW dword 52
- reg set value ELW dword 36
- reg set value EnableCursor dword 0
- display mode set 100
- reg save
next I put more vebose mode by enter in ndcucfg:
this all settings works with my old netDCU14 rev.1.20 board. And one more point is that mentioned LCD also works with display mode set 10 with old board.
But with my two new netDCU14 rev.1.22 boards there is only waveing white strips on black screen.
-
Hello,
don't think the problem is releated to HW V1.22 it was releasesd in 7/2013 and there are no changes concering LCD! Do you see this problem on more then one HW1.22.
What's about bootloader command XDE? Is it Y or N. Should be N.
-
-
Can you please provide me serial number of a "working" and a "non working" board.
-
0754D4_working & 1379CD_new
-
Hello,
these are exactly the same articles and we installed exactly the same SW. So i have no idea what happens here. Can you please send us the boards as RMA (via your distributor) with a detailed description. We will check RGB interface.
Can you please also write me an email with your connection list and registry.
Thanks.
